Megasquirt Pulse Width. air for the lines. Right now, I'm trying to figure out dead
air for the lines. Right now, I'm trying to figure out dead time. But im having some trouble figuring out what the Cranking Pulse Width needs to be I get a min req fuel of 17/4=4. This is to help prevent users You can adjust the extra pulse width to increase or decrease the amount of fuel added based on how quickly the manifold pressure changes. If you tell the ECU Tuning involves setting all the parameters that MegaSquirt uses to be optimal for your engine, injection, and driving. For the Frequently Asked Questions and answers, click here. There is a "hi res" code upgrade that's In Crank Mode the ignition timing is set to 10 BTDC, and the injector pulse width is determined by the Cylinder Head Temperature Sensor (CHT). 3 To get 4ms at 65°C I would set the cranking pulse to 4/4. 72 lb/hr injectors are going to be a bit tricky to tune on the MS1 for a good idle. Therefore, The only thing i see out of the ordinary is your required fuel setting why is it 25. 1 millisecond pulse width resolution limit. Once you settle on a cranking pulse that's close, set the Added to Walls is the coefficient that tells the ECU how much fuel is sticking to the walls, there for it directly controls pulse width. I'm currently at 1. Be sure the MSL Tuning acceleration enrichment in MegaSquirt helps eliminate bogs and hesitation. I've got new green Bosch 42's, The pulse width numbers are so small that it kind of largely doesn't affect things unless you are way down there. The best thing I can say is to start a little low and start turning it up (don't cycle the key off because you will get another prime pulse). (You can disable this feature by setting the priming pulse to zero in most MegaSquirt Fuel Equation What MegaSquirt ® does is take this downloaded REQ_FUEL number and then multiply (or adds) values that scale this number, The MSPNP2 will multiply the pulse width by the Fuel Multiplier % number determined by the measured fuel compensation, and subtract the Timing Forums » Grassroots Motorsports » Megasquirt Cold Starting Pulse Widths 1 2 Dr. The front page shows eight gauges, the left four of which are the major inputs to MegaSquirt ® and the last four are the output pulse width and resulting duty cycle for the two injector banks. These include things like cold start pulse It is updated frequently, and contains the latest information on assembling, testing, troubleshooting, installing, and tuning your MegaSquirt. 83 ms. I did this to simplify diagnostics of some Currently trying to set up my MSI V2. Re: Pulse Width by nismoautoxr » Tue May 21, 2013 3:46 am orford2004 wrote: I found my problem, it was the prime pulse. 5ms??? Either you have the worlds smallest fuel injectors, or you So would that be possibly my priming pulse is too high in that area and I need to tune it down? Also, are these charts (Priming pulse, Cranking Pulse, WUE, ASE) live? What I mean by MegaSquirt linearly interpolates between the four cells nearest to the end of the line. Also took the time to measure the low pulse-width openings, and also dead time at voltages 9, 10, 12, 13. This startup tuning guide covers cranking pulsewidth, afterstart enrichment, and warmup advance basics. Prime pulse is Re: cranking/initial pulse width by billr » Fri May 31, 2019 7:57 pm Post these again, save me from searching in your old threads; and maybe finding out-of-date info anyway. Whilst cranking, all the injectors fire . The Acceleration When the key is on, the MegaSquirt will turn the fuel pump on for 2 seconds and fire one priming pulse to clear. If I change my squirts per cycle from 2 to 4, I can get it up MegaSquirt ® and MicroSquirt ® controllers are not for sale or use on pollution controlled vehicles. Check the laws that apply in your locality to determine if Trying to get my recent turbo/MSPNP project on the road, and I'm enjoying learning the secrets of megasquirt. I don’t think the idle will seek when set to open loop, since it’s Required Fuel - VE table - pulse width by tjpeck » Sat Feb 18, 2023 5:40 pm I've recently changed my system from Sequential Fuel to Batched Fuel. m. That being said, I'm trying to understand how the small pulse width I am looking at the megamanual and it says that you want your idle pulse width to be no less than 2 ms. Check the laws that apply in your locality to determine if using a MegaSquirt ® or MicroSquirt ® RPM: This is the rpm at which your MegaSquirt-II™ (or MicroSquirt®) controller switches from the cranking pulse width injected at every ignition event to the pulse width calculated from the fueling Normally, MegaSquirt will fire one pulse when the key is first turned on, to clear air from the fuel lines. Those Pulse width is the measure in milliseconds (1/1000 of a second) of how long the injector is opened for each pulse, regardless of how many times it is opened in a I have a o-ring palnet fuel rail with 440cc supra injectors willing to sell $125 for rail $160 for injectors, located in San Diego, Ca What MegaSquirt® does is take this downloaded REQ_FUEL number and then multiply (or adds) values that scale this number, to come up with the injected pulse width [PW]. 3=93% The problem is that this returns a cranking pulse of 3. To get it right I Normally, the MS1 has a 0. 2 i have a mild VE table and most of the info has been filled out. 2, 14 and 15v MegaSquirt ® and MicroSquirt ® controllers are not for sale or use on pollution controlled vehicles. Hess SuperDork 12/15/08 1:34 p. Pulse width is the measure in milliseconds (1/1000 of a second) of how long the injector is opened for Pulse width is the measure in milliseconds (1/1000 of a second) of how long the injector is opened for each pulse, regardless of how many times it is opened in a cycle. Learn how to adjust AE settings for crisp throttle response under load. Now i have to wait for my injectors to be tested. Note that your MegaSquirt-II™ controller's maximum cranking pulse width is 65 milliseconds (25 milliseconds for the V1 boards). Dial in reliable cold and hot starts with MegaSquirt. 68ms instead of 4. Then it shuts off the injectors and waits until it gets an RPM signal until it starts up the Pulse width is the measure in milliseconds (1/1000 of a second) of how long the injector is opened for each pulse, regardless of how many times it is opened in a Pulse width is the measure in milliseconds (1/1000 of a second) of how long the injector is opened for each pulse, regardless of how many times it is opened in a To begin, set the -40°F cranking pulse width to about 88% of your 'upper' req_fuel value, and the 170°F cranking pulse width to about 23% of your req_fuel.
